• Non disponibile

2607017468 - Set frese da 6 pz. Trim&Edging codolo da 6 mm 6-piece Trim and Edging Router Bit Set.

30,13 €
Tasse incluse
Guida alle taglie
Guida alle taglie
CLOTHES
MEASUREXS/34S/36M/38-40L/40-42
UK681012
USA46810
FRA36384042
Waist (cm)64687276
Chest (cm)81858993
Seat (cm)899397101
Inseam (cm)81828384


SHOES
FOOT IN INCHESFOOT IN CMUSAEuroUK
23.56395
24.16.539.55.5
24.87.5406
1025.48417
10¼25.78.541.57.5
10½269428
10¾27.39.542.59.5

How to Take Clothing Measurements

  1. Get a flexible measuring tape. These are often sold in craft stores
  2. Neck:
    • Measure around the base of the neck in inches.
    • Round up to the nearest half inch.
  3. Chest:
    • Wrap tape measure under armpits around fullest part of chest (usually right above nipples
  4. Sleeve:
    • Bend your elbow and rest your hand on your hip.
    • Have someone measure from the middle of the back of your neck to your wrist by putting the tape measure over your shoulder, around your elbow and to your wrist.
  5. Waist:
    • Wrap tape measure around where you normally wear your pants. Keep tape measure a little loose by keeping a finger between the tape measure and your waist.
  6. Inseam:
    • Put on a pair of shoes.Have someone measure from your crotch to back of the heel, where you want your pants to end.
  7. Hands:
    • Measure around the hand at the fullest part (exclude thumb). The number of inches shows the size of the glove.
Quantità
  Non disponibile

  Pagamento sicuro

Tramite carta di credito o PayPal

  Spedizioni rapide

Spedizioni assicurate entro 24/48h

  Possibilità di reso

Se non sei soddisfatto dell'acquisto avrai la possibilità di effettuare il reso del prodotto

Il set frese consente tagli fini per una varietà di applicazioni, che lo rendono la scelta ideale per carpentieri, falegnami, installatori di interni e operai edili. I taglienti in metallo duro delle frese garantiscono lunga durata, mentre la fresatura di una varietà di profili in molti materiali diversi è possibile grazie alle diverse geometrie di taglio. Inoltre, sono fabbricati secondo le norme di sicurezza di DIN EN-847. Le frese sono destinate all'uso nel legno tenero, nel legno duro e nel legno composito. Il set frese Trim&Edging, 6 pz., comprende frese di lavorazione bordi per rifilatura e arrotondamento e presenta inoltre ricambi aggiuntivi quali una chiave esagonale e due cuscinetti a sfere. Il set frese presenta un intaglio con speciale design Easy-Pick, che consente alle frese di essere estratte dal codolo con velocità e sicurezza. Comprende una custodia esclusiva e molto solida che trattiene saldamente le frese, per una perfetta protezione del contenuto e uno stoccaggio e un trasporto in sicurezza. Presenta un coperchio trasparente per la visibilità del contenuto. Il set è disponibile in tre versioni, con diametro codolo da 6 mm, 8 mm o ¼" per coprire la compatibilità con tutte le comune fresatrici portatili.

Dettagli del prodotto

2607017468

Presto Compara

Prodotto
2608577014 - Punta Forstner da 32 mm 32 x 90 mm, d 10 mm, toothed-edge 2608628398 - Bit di formatura bordi H, 8 mm, R1 2,4 mm, D 12,7 mm, L 12,4 mm, G 46 mm 8 mm, R1 2,4 mm, D 12,7 mm, L 12,4 2608628468 - Fresa dritta, 12 mm, D1 20 mm, L 40 mm, G 81 mm 12 mm, D1 20 mm, L 40 mm, G 81 mm 2608628407 - Bit per scanalature a V, 8 mm, D1 16 mm, L 16 mm, G 45 mm, 90 gradi 8 mm, D1 16 mm, L 16 mm, G 45 mm, 90 gr
Availability
Prezzo
18,08 €
18,08 €
18,08 €
18,40 €
Descrizione

2608577014 - Punta Forstner da 32 mm 32 x 90 mm, d 10 mm, toothed-edge

2608628398 - Bit di formatura bordi H, 8 mm, R1 2,4 mm, D 12,7 mm, L 12,4 mm, G 46 mm 8 mm, R1 2,4 mm, D 12,7 mm, L 12,4

2608628407 - Bit per scanalature a V, 8 mm, D1 16 mm, L 16 mm, G 45 mm, 90 gradi 8 mm, D1 16 mm, L 16 mm, G 45 mm, 90 gr

Nessun articolo da comparare