2608596821 - Punte per metallo HSS-G, DIN 340 5,5 x 91 x 139 mm

17,13 €
Tasse incluse 1-2 giorni lavorativi

2608596821 - Punte per metallo HSS-G, DIN 340 5,5 x 91 x 139 mm

Guida alle taglie
Guida alle taglie
CLOTHES
MEASUREXS/34S/36M/38-40L/40-42
UK681012
USA46810
FRA36384042
Waist (cm)64687276
Chest (cm)81858993
Seat (cm)899397101
Inseam (cm)81828384


SHOES
FOOT IN INCHESFOOT IN CMUSAEuroUK
23.56395
24.16.539.55.5
24.87.5406
1025.48417
10¼25.78.541.57.5
10½269428
10¾27.39.542.59.5

How to Take Clothing Measurements

  1. Get a flexible measuring tape. These are often sold in craft stores
  2. Neck:
    • Measure around the base of the neck in inches.
    • Round up to the nearest half inch.
  3. Chest:
    • Wrap tape measure under armpits around fullest part of chest (usually right above nipples
  4. Sleeve:
    • Bend your elbow and rest your hand on your hip.
    • Have someone measure from the middle of the back of your neck to your wrist by putting the tape measure over your shoulder, around your elbow and to your wrist.
  5. Waist:
    • Wrap tape measure around where you normally wear your pants. Keep tape measure a little loose by keeping a finger between the tape measure and your waist.
  6. Inseam:
    • Put on a pair of shoes.Have someone measure from your crotch to back of the heel, where you want your pants to end.
  7. Hands:
    • Measure around the hand at the fullest part (exclude thumb). The number of inches shows the size of the glove.
Quantità
  Ultimi articoli in magazzino

  Pagamento sicuro

Tramite carta di credito o PayPal

  Spedizioni rapide

Spedizioni assicurate entro 24/48h

  Possibilità di reso

Se non sei soddisfatto dell'acquisto avrai la possibilità di effettuare il reso del prodotto

La punta lunga per metallo HSS rettificata è adatta per forare in profondità il metallo con la massima precisione. Grazie alla maggiore lunghezza, questa punta lunga è in grado di forare in profondità. La punta HSS rettificata con angolo di spoglia di 135 gradi unisce il taglio attivo e il perfetto centraggio senza slittamenti, offrendo la massima precisione. La punta per metallo HSS con affilatura e rettifica di precisione elimina anche la necessità di eseguire la preforatura o la foratura pilota fino a 10 mm, consente di ottenere un avanzamento della foratura più rapido del 40% ed una forza di spinta inferiore del 50% rispetto alle punte in HSS con rettifica standard ed affilatura conica. Punta lunga per metallo HSS rettificata, angolo di spoglia 135 gradi, affilatura quadrupla secondo DIN 1412 C, tolleranza del diametro h8. Per acciaio legato e non legato fino ad una resistenza alla trazione di 900 N/mm2, acciaio forgiato, ghisa grigia, ferro sinterizzato, ghisa malleabile, metalli non ferrosi, plastica dura. Codolo cilindrico, per impiego con trapani avvitatori e a colonna.

Dettagli del prodotto

2608596821
2 Articoli

Presto Compara

Prodotto
2608577060 - Punta elicoidale HSS con attacco esagonale 7,0 mm 7 x 69 x 109 mm 2608577128 - Punta elicoidale HSS con attacco esagonale 7,5 mm 7.5 x 69 x 109 mm 2608577061 - Punta elicoidale HSS con attacco esagonale 8,0 mm 8 x 75 x 117 mm 2608595686 - Punte per metallo HSS-G, DIN 340 6,5 x 97 x 148 mm
Availability
Prezzo
5,08 €
5,08 €
5,16 €
5,48 €
Descrizione

2608577060 - Punta elicoidale HSS con attacco esagonale 7,0 mm 7 x 69 x 109 mm

2608577128 - Punta elicoidale HSS con attacco esagonale 7,5 mm 7.5 x 69 x 109 mm

2608577061 - Punta elicoidale HSS con attacco esagonale 8,0 mm 8 x 75 x 117 mm

2608595686 - Punte per metallo HSS-G, DIN 340 6,5 x 97 x 148 mm

Nessun articolo da comparare