2608577309 - Punta elicoidale HSS PointTeQ da 15,5 mm (attacco ridotto)

11,29 €
Tasse incluse 1-2 giorni lavorativi

2608577309 - Punta elicoidale HSS PointTeQ da 15,5 mm (attacco ridotto)

Guida alle taglie
Guida alle taglie
CLOTHES
MEASUREXS/34S/36M/38-40L/40-42
UK681012
USA46810
FRA36384042
Waist (cm)64687276
Chest (cm)81858993
Seat (cm)899397101
Inseam (cm)81828384


SHOES
FOOT IN INCHESFOOT IN CMUSAEuroUK
23.56395
24.16.539.55.5
24.87.5406
1025.48417
10¼25.78.541.57.5
10½269428
10¾27.39.542.59.5

How to Take Clothing Measurements

  1. Get a flexible measuring tape. These are often sold in craft stores
  2. Neck:
    • Measure around the base of the neck in inches.
    • Round up to the nearest half inch.
  3. Chest:
    • Wrap tape measure under armpits around fullest part of chest (usually right above nipples
  4. Sleeve:
    • Bend your elbow and rest your hand on your hip.
    • Have someone measure from the middle of the back of your neck to your wrist by putting the tape measure over your shoulder, around your elbow and to your wrist.
  5. Waist:
    • Wrap tape measure around where you normally wear your pants. Keep tape measure a little loose by keeping a finger between the tape measure and your waist.
  6. Inseam:
    • Put on a pair of shoes.Have someone measure from your crotch to back of the heel, where you want your pants to end.
  7. Hands:
    • Measure around the hand at the fullest part (exclude thumb). The number of inches shows the size of the glove.
Quantità

  Pagamento sicuro

Tramite carta di credito o PayPal

  Spedizioni rapide

Spedizioni assicurate entro 24/48h

  Possibilità di reso

Se non sei soddisfatto dell'acquisto avrai la possibilità di effettuare il reso del prodotto

La punta per metallo HSS PointTeQ velocizza la foratura nel metallo grazie alla punta PointTeQ. È possibile avviare con facilità e rapidità la foratura poiché la punta auto-centrante evita gli spostamenti. Grazie alla maggiore velocità di foratura, viene generato meno calore. La punta PointTeQ rimane affilata e garantisce una durata ininterrotta. Questo bit è idoneo per praticare fori di centraggio e passaggio in acciaio legato e non legato, metalli non ferrosi, acciaio forgiato, ghisa e plastiche. Il rischio di rottura è ridotto, specialmente per le punte con diametro inferiore a 6 mm poiché la punta è realizzata con un corpo altamente elastico. La spirale rivestita di ossido nero consente un'asportazione rapida dei trucioli. La punta per metallo HSS PointTeQ è realizzata secondo DIN 338, è una punta tipo N (angolo di spirale) con angolo di spoglia 135 gradi. Codolo cilindrico, per impiego con trapani avvitatori e a colonna.

Dettagli del prodotto

2608577309
4 Articoli

Presto Compara

Prodotto
2608595069 - Punte per metallo HSS-G, DIN 338 6,8 x 69 x 109 mm 2608585838 - Punte per metallo HSS-Co, DIN 338 1 x 12 x 34 mm 2608585839 - Punte per metallo HSS-Co, DIN 338 1,5 x 18 x 40 mm 2608585840 - Punte per metallo HSS-Co, DIN 338 2 x 29 x 49 mm
Availability
Prezzo
0,00 €
1,17 €
1,30 €
1,40 €
Descrizione

2608595069 - Punte per metallo HSS-G, DIN 338 6,8 x 69 x 109 mm

2608585838 - Punte per metallo HSS-Co, DIN 338 1 x 12 x 34 mm

2608585839 - Punte per metallo HSS-Co, DIN 338 1,5 x 18 x 40 mm

2608585840 - Punte per metallo HSS-Co, DIN 338 2 x 29 x 49 mm

Nessun articolo da comparare